How to make more sockets on the wall

A house with a lot of people needs a lot of outlets to avoid unnecessary fights. Learn how to install outlets yourself.

It’s no surprise that there are often small fights at home over a lack of outlets, or maybe it’s because we now use too many devices that need that outlet. But you probably also came across a moment when you had to charge, for example, your cell phone and There are not enough sockets at homeNow is the time to discreetly turn off another family member’s tablet and pretend nothing happened.

Don’t worry, this won’t happen anymore because today we will explain to you How can you propagate sockets through registration boxes?We assure you that it is very simple and, above all, very useful.

outlet overload when connecting a large number of devicesoutlet overload when connecting a large number of devices

Take paper, pen, win and aim, these are the tools you will need in this small repair: a screwdriver, special scissors for working with electricity, a flowerpot, a saw, a chisel and a trowel. As for materials, it is advisable to have with you: plaster, glue gutters, electrical cables, corrugated tube and sockets.

How to install more outlets at home

If you are not very fond of DIY, bother us orWe’ll walk you through step by step how to complete this simple installation.We will also explain exactly what tools and materials we are going to use.

The first essential step you need to take to be able to install more outlets in any room of your house is to turn off the electrical current throughout the house. This step is absolutely necessary. Next we need to decide where we want to place the base of the socket and mark it so that then draw a line with a pencil what route the slash will have to take. For those who don’t know the term, in the DIY world, the route we need to make in the wall to run electrical cables is called a slash. This will then be sealed with plaster.

Universal stripUniversal strip

The most appropriate thing for a small electrical installation is that if we do not want to place many plugs, but only a couple, it is better to make small holes in the wall instead of a whole hole, since later they will be easier to close and also easier to make. Using a chisel and a small hammer-pot- We will open holes in the wall and then run the cables through the same place.

Next we will need to make a small hole in the wall to install the new outlet box using a chisel and hammer. It won’t take us too longRemember, it’s better to open a small hole and make it bigger than to have to close it later.

it's time to correct the wall defects when installing the plugit’s time to correct the wall defects when installing the plug

Once we have made all the holes in the wall, including the socket box, we will need to lay the corrugated cable, depending on which one best suits our needs, we must consult a specialist. corrugated cable This is an electrical conduit designed to protect and route electrical cables.fundamental is also necessary because it also provides flexibility to the cables and insulates them.

Now comes the time to fill the cracks with plaster, following the mixing measurements specified by the manufacturer. Before applying the plaster with a spatula, don’t forget to close the box with sockets so that it does not get stained or leftover material gets on it.

The most difficult stage is to route the cables from the new box to the registration box, here you will have to pay a lot of attention, with patience and attentiveness you will achieve a good result. To route the wiring from the new box to the registration box, we will have to do via cable entry or an electrician’s guide to connect the cables and then pull the cable entries until they come out through the conduit from one groove to the other.

Overloaded socketOverloaded socket

We carefully screw the lid of the box, connect new plugs, now check the functionality of the plugs and finally install the casing and, if we deem it appropriate, we can paint over the lid.

It’s time to give the room some color again and paint over those holes that we made for the wiring and which then had to be covered with plaster.

Another option, if for example we want to accommodate one or two more plugs, is to avoid making scratches or holes in the wall to avoid damaging them, and run the wiring from the new box to the registration box. through self-adhesive guttersWith. A very convenient and economical option that does not require so much time, but, however, the aesthetic result will not be the same.

Leave a Comment